Learning how to install ceramic floor tile is easy! All you need to do is to get your hands on the right step-by-step instruction and follow these basic and straightforward steps. The next thing you know, you’ll be able to bring your desired floor design to life.
Get the right tools for the job.
For starters, if you want to know how to install ceramic floor tile by yourself, you should have the right tools and materials for the job. You can easily buy, or rent, most of the tools and materials you’ll need at you neighborhood hardware store, or home center. For equipment that would be too expensive like a tile cutter, or hand held micro cutter, you may be able to rent these tools from your local home center or a tool rental yard. Here are most of the basic tools you will need for your tiling job:
a) Wear safety gear and clothing. Use a pair of safety glasses, heavy leather gloves, and long-sleeved work clothes, especially if it involves taking out the existing ceramic tiles. Broken shards and other debris can cause nasty cuts, if you are not careful. b) A tape measure, tile spacers, carpenter’s square and a bubble level. c) A mallet and hammer, a putty knife and a trowel (preferably, the notched kind), and a rubber grout float and a putty knife. d) A tile cutter (which may be rented) and a pair of tile nippers. e) Mortar material like a thin set mortar, or any one of a wide selection of tile adhesives. f) Tiling grout and sealant. Tiling grout comes in many color tints that you can choose from to fit your desired look and floor design.
Prepare your subfloor before installing your tiles.
The tiling part of the project starts here. It would be a great experience for you to learn how to install ceramic floor tile by learning about the type of floors you will be putting your tiles on. Always check for cracks and debris when If you’re working on a concrete subfloor. Make it is smooth and clean. Repair as many of the cracks as you can. If you see cracks that are too large to repair, replace the floor section where they are found with new concrete. For plywood subfloors, be sure that the wood is at least 1 and 1/8 inches thick and is supported by an equally strong underlayment. Otherwise, your ceramic tiles will dislodge easily, or worse, break and need replacing.
An existing ceramic tile floor may add another stage to your tiling job, and present something of a challenge for you. You’ll need to tear out the existing tiles. For starters, all you need to do is use a large flat-bladed chisel and a mallet, and just hammer away. Then, you’ll need to clean out the debris. If you to smoothen your subfloor — you may want to rent a sander to do the job. Be sure to keep yourself protected. Use heavy-duty leather work gloves, safety glasses, and long-sleeved work clothes.
Lay out your floor.
Measuring the length and width of your floor will help you determine how to install ceramic floor tile and help you know estimate the number of ceramic floor tiles you will need to purchase. Start by finding the center point of your floor area. You can do this by measuring across the room and marking the center. Do this in opposite direction and mark the center, as well. The intersection of the two lines is the center of the floor you will be tiling over. Run chalk lines over the intersection lines. These chalk lines will help you with how to install ceramic floor tile and with your tile positioning.
Let the tiling begin!
The first tile should be placed at the intersection of the two lines you made. Then, bond it to your subfloor by using a thin set mortar, or a tile adhesive of your choice. Using a notched trowel for applying the mortar is best on how to install ceramic floor tile. But you may actually use the more common trowel variety is you don’t have one. To secure the ceramic tile in its place, press down while twisting it back and forth till the tile no longer is set. If some of the mortar or adhesive oozes out, use your trowel (or a damp sponge) to scrape off the excess. Do this process over with the next tile, and so on and so forth, until you’ve finished your ceramic floor tiling.
Time to grout and seal.
The next step is to grout the floor once your tiles are settled. Tiling grout is a material that you should know more about when you want to know how to install ceramic floor tile flooring. Tiling grout is a material made cement, sand and water, and a little color. It is used to fill in gaps and seal in the spaces between tiles. Tiling grout comes in a wide variety of color tints that may be matched to your tile color. Use a rubber grout float and work the tiling grout into the gaps between the tiles. Use your grout float at an angle so that you can fill in the joint gap with as much tiling grout as possible.
After laying in the tiling grout in between the gaps of your floor ceramic tiles, use a damp sponge to wipe off the excess grout. Rinse the sponge frequently to get as much of the excess grout off, and keep each tile clean. You have the option of applying a sealant to the grout lines after they dry.
Now you have new ceramic tile floor! Learning about how to install ceramic floor tile is easy! By following these basic steps, you too can realize your ceramic floor design. Learning how to install ceramic floor tile properly will give you a sense of satisfaction at a job well done, and a beautiful ceramic tiled floor.